You are here: PANDA Wiki>DCS Web>SupportedHardware (revision 42)EditAttach

Supported Hardware

This page shows the hardware used by the individual sub-detectors.
To minimize the development and maintenance costs the DCS core group recommends to use common solutions if possible.

High Voltage (HV)

ISEG EHS/EDS high voltage modules

Low Voltage (LV)

Wiener PL500 / Wiener MPOD

Front-end electronics (FEE)

Gas systems

Vacuum systems

Pfeiffer Vacuum HiPace300 with TCP350 remote controller (Turbo molecular pump) Edwards nXDS15i (Scroll pump) Pfeiffer Vacuum DigiLine Transmitter (Gauges)

Cooling systems

Huber Unistate 425w THMP PT100 (EMC)

The self-made PT100 for the EMC are based on a 50 cm long platinum wire with a diameter of 25 µm. The platinum wire is brought onto a self-adhesive Kapton film and covered with a non-adhesive film on the back-side. The measurement is to take place via a four-terminal sensing, which allows to ignore the resistance of the supply wires to the point where the sensor starts. This is a common method to ensure high-precision resistance measurements. The resistance of the sensor at 0 °C is chosen to be 100 Ohms to provide comparability to commercial PT100-sensors and to obtain measureable voltages with a testing current of only 1 mA. For read-out the THMP will be used. -- FlorianFeldbauer - 25 Sep 2009

Humidity Sensors (EMC)

For the humidity measurement inside the EMC the sensors HIH4000-003 from Honeywell are used. For read-out the THMP will be used. -- FlorianFeldbauer - 25 Sep 2009

Pressure sensors
  • Commercial sensors, type MPXAZ4115A6U from Semiconductor Technologies, measure the relative pressure inside the EMC within a range from 15 to 115 kPa. The output voltage is between 0.2 and 4.8 V DC, and the supply voltage is 5 V. Here again, the reading out is carried out by the THMP. -- PatrickFriedel - 17 Jan 2013. datasheet
  • Swagelok Pressure Transducers S Model with milliampere output signal are used for measuring the pressure inside the cooling pipes for the luminosity detector. Read out via THMP. -- FlorianFeldbauer - 01 Feb 2013. link
Production of extremely thin sensor cables (EMC)

The very thin cables (90 µm thick) are mainly used for the self-made thin PT100 temperature sensors, but they can also be utilized for the humidity and pressure sensors. They are made from a two-layer copper/polyimide foil, type Pyralux AC182500R from DuPont. An exposure mask is used for the copper layer. The layout of the mask for the temperature sensor cables is to be found at: ExpMask_TempCable.png Please refer to ExpMask_HumExtCable.png for the layout of the humidity sensor cables and the extension cable. The layouts are printed twice on DIN-A3 transparent foils, and by putting the foils above each other, an adequately dark exposure mask is obtained. Then the non-exposed areas are etched off and single cables are cut out and covered with self-adhesive Kapton foil. -- PatrickFriedel - 17 Jan 2013

Movement / Position monitoring

Other Hardware

Light Pulser (EMC)

EPICS Support

IOC/Hardware EPICS support is listed here:

Irradiation Tests of Electronic Components

Target CompactRIO controller

For the target subsystem, we will use a CompactRIO controller running LabVIEW, which will communicate with the main EPICS system. More specs, documentation, link to Andrea's talk (GSI, Dec 2009).

ALERT! The recommended LabVIEW version to use is 2009.

ALERT! Look into COSYLAB module for CompactRIO:

Additional hardware used for test setups

Wiener VME crate remote control

Voetsch VT-4021


Julabo FP50-HL Julabo LH47 Presto

TMCM142 high-performance single axis stepper motor controller/driver

Topic attachments
I Attachment Action Size Date Who CommentSorted ascending
Datasheet_VPT_Preamp_SP883a01.pdfpdf Datasheet_VPT_Preamp_SP883a01.pdf manage 1453.1 K 02 Sep 2011 - 16:40 AndreaWilms Datasheet for the low power/low noise (LNP) charge preamplifier SP883a01 for VPT readout
Datasheet_APD_Preamp_SP883a02.pdfpdf Datasheet_APD_Preamp_SP883a02.pdf manage 1827.6 K 26 Aug 2011 - 08:25 AndreaWilms Datasheet for the low power/low noise (LNP) charge preamplifier SP883a02 for APD readout
MIC5200_datasheet.pdfpdf MIC5200_datasheet.pdf manage 173.4 K 25 Sep 2009 - 11:41 FlorianFeldbauer Datasheet of the voltage regulator MIC5200 from MICREL
SP883d_Datasheet_Manual_PreampV0.5.8.pdfpdf SP883d_Datasheet_Manual_PreampV0.5.8.pdf manage 11698.3 K 24 Aug 2011 - 08:40 AndreaWilms Preliminary user manual for the low power/low noise (LNP) charge preamplifier for Panda EMC proto 192
LNP_Q_Preamp_SP883_3_0.pdfpdf LNP_Q_Preamp_SP883_3_0.pdf manage 882.5 K 12 Oct 2009 - 10:59 AndreaWilms Specs of Low Noise preamplifier for APD/VPT readout
Edit | Attach | Print version | History: r45 | r43 < r42 < r41 < r40 | Backlinks | View wiki text | Edit WikiText | More topic actions...
Topic revision: r42 - 24 Jan 2019, FlorianFeldbauer
This site is powered by FoswikiCopyright © by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding PANDA Wiki? Send feedback
Imprint (in German)
Privacy Policy (in German)